SENSORMATE STRAIN SENSOR

Product Details:

The magnetic strain gauge sensor QE1008-W measure the surface-strain directly at the mounting location in the same quality as bonded strain gages. The magnetic press-on technology, developed by Sensormate AG, presses the strain gauges under the stainless protective film so strongly against the surface to be measured that frictional contact occurs.The mounting of the sensor is non-destructive, very fast and simple.
Main features:•Direct measurement of surface strain•Quick and non-destructive assembly with magnetic press-on technology•High accuracy and linearity in tension and pressure(like bonded strain gauges)•Ideal for use on presses, injection-moulding and die-casting machines•Application on tie bars with a diameter of 45mm or higher and flat surfaces•Dynamic applications•Without amplifier (passive)

Additional Information:

• Delivery Time: READY STOCK

Product Details:

The magnetically mounted wireless strain sensor QE2008-W measures thestrain directly at the location where is mounted, providing a measurementthat has the same quality and performances as with bonded strain gauges.The Sensormate press-on technology implements a strain gauge positionedunder a stainless protective film. When the sensor is mounted on a metallicobject, the magnets hold so strictly that frictional contact occurs and allowsa reliable measurement.The mounting of the sensor is quick, simple and non-destructive, allowingfor an easy setup and increasing the daily productivity.The integrated electronics contains a state-of-the-art processing component,which allows hi-end measurements and wireless communication via theBluetooth 5.0 protocol. The adopted components allows for a low-energyoperation, extending the battery life to several working hours.An on-board accelerometer allows the user to check the correct mounting ofthe sensor and assure an accurate measurement result. The internal RAMmemory helps when a fast measurement is needed, allowing to store highresolution data.

Typical Applications:• Injection-moulding machines- Tie Bar parallelism check- Bending analysis- Cavity pressure profile inspection- Tie bar cracks detection• Die casting machines• Presses• Structural monitoring• Indirect load and force measurement

Main features:• Wireless system for strain measurementswith Bluetooth 5.0• Press-on strain gauge technology(quick and non-destructive mounting)• Easy mounting via magnetic holding onflat and round surfaces (diameter ≥ 45mm)• Visualization of the measurements viathe “Sensormate App” (available forWindows, Android and iOS)• High performance amplifier integrated ineach sensor with high resolution and fastsampling rate• Integrated LiPo battery with long operatingtime (> 12h)• Integrated accelerometer for mountingguidance

Product Details:

Features:•Complete system for the simultaneous strain-measurement on up to four tie bars•Direct display of strain values in με, kN or t(via our Inspectmate software)•Quick and non-destructive assembly with magnetic press-on technology•High accuracy and linearity in tension and pressure (like bonded strain gauges)•Ideal for use on presses, injection-moulding and die-casting machines•Application on tie bars with a diameter of 45mm or higher and flat surfaces•Dynamic applications•4- channel digital monitor-box DU-4USB•USB connection for tie bar adjustment software and power supply•Very compact and easy to use system

Additional Information:

• Delivery Time: 06 to 08 Working Week

Product Details:

The strain gauge sensor GE1029-A measure the surface-strain directly at the mounting location in the same quality as bonded strain gages. The integrated variable digital amplifier amplifies the signal on the spot, avoiding EMC problems. The sensor does not have to be recalibrated between remove and re-installation. The press-on technology, developed by Sensormate AG, presses the strain gauges under the stainless protective film so strongly against the surface to be measured that frictional contact occurs. The sensor is mounted using stainless steel straps, is non-destructive, very fast and simple. For each tie-bar diameter outside tolerance of ± 2.5mm a different pair of steel straps is required. The sensor can not be overloaded. The GE1029-A sensors require a cyclic reset.

Additional Information:

• Delivery Time: READY STOCK

Product Details:

• Complete system for the strain-measurement on one tie bar
• Direct display of strain values in with, kN or t
• Quick and non-destructive assembly with magnetic press-on technology
• High accuracy and linearity in tension and pressure(like bonded strain gauges)
• Ideal for use on presses, injection-moulding and die-casting machines
• Application on tie bars with a diameter of 45mm or higher and flat surfaces
• Dynamic applications
• 1- channel digital monitor DU1D
• Battery operation possible (optional) / not rechargeable
• Very compact and easy to use system

Product Details:

The magnetic strain gauge sensor QE1008-W measure the surface-strain directly at the mounting location in the same quality as bonded strain gages. The magnetic press-on technology, developed by Sensormate AG, presses the strain gauges under the stainless protective film so strongly against the surface to be measured that frictional contact occurs. The mounting of the sensor is non-destructive, very fast and simple. The integrated signal amplifier with wireless transmission module makes the QE1008-W a state-of-the-art sensor with unsurpassed features and user-friendliness.

Main features:
• Complete system for the simultaneous strainmeasurement on up to four tie bars
• Direct display of strain values in με, kN or t (via our Inspectmate software or Sensormate App)
• Wireless transmission (2.4GHz), no cables
• Quick and non-destructive assembly with magnetic press-on technology
• High accuracy and linearity in tension and pressure (like bonded strain gauges)
• Ideal for use on presses, injection-moulding and die-casting machines
• Application on tie bars with a diameter of 45mm or higher and flat surfaces
• Dynamic applications
• Each magnetic-mount strain sensor has an integrated signal amplifier
• Integrated rechargeable battery with up to 8h operating time
• Receiver with USB interface or receiver with bluetooth 5 low energy interface
• Very compact and easy to use system

Product Details:

Main features• With 4-channel digital monitor DU-4D (active)• Dynamic applications• Presses, injection moulding and die-casting machines• One system for all tie bar diameters• Very high accuracy (like bonded strain gauges)• Measured strain value directly in με, kN or tons• USB interface for alignment software (optional)• Analog output 0...10VDC (optional)• Compact system and simple application